❄ TurfLocalFree tools for everyday projects

Bay Area rules guide

The Bay Area gas furnace rule: what it means for your furnace

What the Air District's Rule 9-4 requires, what it does not, the dates that moved in 2026, and how to choose between repairing, replacing with gas, or switching to a heat pump if your furnace is failing now.

Short answer. Nobody has to remove a working gas furnace. The Bay Area Air District's Rule 9-4 sets a zero-NOx standard for residential and commercial furnaces manufactured from January 1, 2029, and the Air District says the requirements apply only when your current equipment burns out. Until that date, a new gas furnace can be installed if it meets the ultra-low NOx standard that has applied to residential central furnaces since January 1, 2024. If your furnace is old enough that you expect to replace it within a few years, get a heat pump quote as well as a gas one, because an electric heat pump already meets the 2029 standard. The water heater date moved on November 4, 2026, and the furnace rule was due back before the Air District's board on December 2, 2026, so check the Air District's page for changes after that.

Contractor lookup has ended

TurfLocal no longer lists HVAC contractors. Already have a quote? Check it free with HVAC Quote Check. More free tools: all TurfLocal tools.

What the rule actually requires

The Bay Area Air District regulates the nitrogen oxides (NOx) that gas appliances give off. Two of its rules cover home heating: Rule 9-4 for furnaces and Rule 9-6 for water heaters. Both are point-of-sale standards. They set what new equipment must meet, and the Air District says the new requirements "apply only upon burn out of one's current equipment". Its fact page is blunter: "There is no mandate to remove or replace functioning appliances before they fail."

EquipmentStandardApplies to units manufactured from
Residential fan-type central furnaces (the usual forced-air furnace)Ultra-low NOxJanuary 1, 2024, already in force
Residential and commercial furnacesZero NOxJanuary 1, 2029
Residential water heaters (the usual home tank)Zero NOxJanuary 1, 2028, moved from 2027 on November 4, 2026
Water heaters from 75,000 BTU/hr to 2 million BTU/hr, including tanklessZero NOxJanuary 1, 2031

Sources: the Air District's Rules 9-4 and 9-6 page (last updated November 5, 2026), its implementation page and its Know the Facts page. Gas stoves, ovens and dryers are not covered.

The standard is written around emissions, not fuel. The Air District says a gas appliance that can show it meets the zero-NOx standard would be allowed. In practice, the zero-NOx options it points homeowners to are electric, and a heat pump is the electric option that heats and cools with one system.

What changed in 2026

Water heaters, November 4, 2026. The Air District's board adopted amendments to Rule 9-6 that move the zero-NOx date for residential water heaters to January 1, 2028. They also add exemptions for qualifying low-income property owners and for properties with significant electrical or space constraints. The rule still applies only when a water heater is replaced.

Furnaces, under review. The Air District held an implementation workshop on the furnace rule on August 27, 2026. HARDI, the trade association of HVAC distributors, reported that staff recommendations would go to the Air District's board on December 2. On the Air District's rule page dated November 5, 2026, the furnace date is still January 1, 2029. If you are reading this after December 2, 2026, check the Air District's page for the outcome before you make a decision that depends on the date.

Your furnace is failing this winter: repair, gas or heat pump?

Nothing in the rule forces a decision this winter. What it changes is the next replacement. A gas furnace installed now can stay until it fails, but new furnaces manufactured from 2029 have to meet the zero-NOx standard. So the real question is how long you expect to keep whatever you install.

Your situationUsually sensibleWhy
A newer furnace with one failed partRepair itThe rule sets standards for new equipment and does not require removing a working furnace. A single part on a sound furnace is routine work.
An older furnace facing a major repair, such as a cracked heat exchanger or a failed inducer or blower motorReplace it, and choose the fuel on purposeWhat you install now is the system you will live with for years, and the one after it falls under the 2029 standard.
Your air conditioner is old too, or you have none and want coolingGet a heat pump quote next to the gas quoteOne heat pump does both jobs, and the Bay Area's mild winters are well within what an air-source heat pump is built for.
Your electrical panel is small or already fullHave the panel assessed before you chooseA heat pump needs electrical capacity. That is the same constraint the new water heater exemptions recognise.

For the money side of a repair, the repair or replace calculator works from your furnace's age and the quote in your hand. If the furnace has simply stopped, start with why a furnace will not turn on, because a fair share of those calls end at the thermostat, the filter or a switch.

What to ask before you sign

  • For a gas furnace: does the model on the quote meet the Bay Area's ultra-low NOx standard for residential central furnaces? Ask the contractor to show it on the quote.
  • For a heat pump: does my electrical panel need work, was the system sized with a Manual J load calculation, and how does it handle the coldest nights we get here?
  • For either: the contractor's C-20 licence number. Check it is active on the CSLB licence check before work starts.
  • Permits: replacing a furnace or installing a heat pump generally needs a permit from your city. Ask who pulls it and when the inspection happens.
  • Or let us check it: upload the quote to HVAC Quote Check. It asks these questions for you and runs the California deposit and license checks.

Incentives in 2026

The federal 25C and 25D tax credits ended for equipment placed in service after December 31, 2025. California's TECH Clean California and HEEHRA single-family heat pump incentives were both fully reserved by February 2026. Our heat pump incentives checker shows what is still open, with the date of each change. The Air District itself points residents to The Switch Is On for current incentives and financing.

FAQ

Common questions

Is the Bay Area banning gas furnaces?

Not in the way the headlines suggest. The Air District's Rule 9-4 sets a zero-NOx emissions standard for new furnaces manufactured from January 1, 2029. It does not require anyone to remove a working furnace, and it applies when equipment is replaced. It gets called a ban because the furnaces that meet a zero-NOx standard today are electric.

Do I have to replace my gas furnace by 2029?

No. The Air District says there is no mandate to remove or replace functioning appliances before they fail. The standards apply to new equipment.

Can I still buy a gas furnace now?

Yes. Until the zero-NOx date, a new residential central gas furnace has to meet the ultra-low NOx standard that has applied to units manufactured since January 1, 2024. Ask the contractor to confirm that the model on your quote meets it.

What if my gas furnace breaks after January 1, 2029?

New furnaces manufactured from that date have to meet the zero-NOx standard, which in practice means an electric option such as a heat pump. Whether a gas unit made before that date can still be installed is a question for your contractor and the Air District. Its board was also due to review the furnace rule on December 2, 2026, so check the Air District's page for the current dates.

Does the rule affect gas stoves, ovens or dryers?

No. The Air District says stoves, ovens, dryers and other cooking appliances are not affected, and that it has no plan to regulate them.

Did the water heater date change?

Yes. On November 4, 2026 the Air District's board moved the zero-NOx date for residential water heaters to January 1, 2028. It also added exemptions for qualifying low-income property owners and for properties with significant electrical or space constraints.